filename: tfs 1526.doc version 1.1 22.05.2013 vectron international filter specification tfs 1526 1/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. measurement condition ambient temperature: 23 c input power level: 0 dbm terminating impedance: input: 50 output: 50 characteristics the maximum attenuation in the pass band is defined as the insertion loss a e . the nominal frequency f n is fixed at 1526mhz without any tolerance or limit . the values of absolute attenuation a abs are guaranteed for the whole operating temperature range. the frequency shift of the filter in the op erating temperature range is included in the production tol erance scheme. d a t a typ. value tolerance / limit insertion loss a e 3.8 db max. 5.0 db nominal frequency f n 1526.0 mhz passband pb f n 3.0 mhz pass band variation 0.2 db 1.0 db absolute attenuation a abs 0.3 mhz ? 1494 mhz 47 db min. 40 db 1494 mhz ? 1506 mhz 41 db min. 35 db 1544 mhz ? 1552 mhz 33 db min. 20 db 1552 mhz ? 1600 mhz 50 db min. 40 db 1600 mhz ? 2000 mhz 45 db min. 35 db group delay ripple within pb p-p 6 ns max. 100 ns operating temperature range otr - 23c storage temperature range - - 40 c ... + 85c temperature coefficient of frequency tc f * -42 ppm/k *) ? f c (hz) = tc f (ppm/k) x (t - t o ) x f cat (mhz). generated: checked / approved: 6 ground
filename: tfs 1526.doc version 1.1 22.05.2013 vectron international filter specification tfs 1526 2/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. filter characteristic 0 200 400 600 800 1000 1200 1400 1600 1800 2000 -60 -50 -40 -30 -20 -10 0 frequency in mhz s21 in db 1486 1494 1502 1510 1518 1526 1534 1542 1550 1558 1566 -60 -50 -40 -30 -20 -10 0 frequency in mhz s21 in db 1486 1494 1502 1510 1518 1526 1534 1542 1550 1558 1566 0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 0.2 frequency in mhz gdr in s construction and pin connection (all dimensions in mm) 1 2 3 4 5 6 1,2 max. 0,6 0,75 3 ,0 +/-0,15 0,6 0,30x0,30 1 3 6 4 date code 50 test circuit l1 saw l2 2 5 1, 3, 4, 6 g26 d24 1 ground 2 input 3 ground 4 ground 5 output 6 ground date code: year + week d 2013 e 2014 f 2015 ...
filename: tfs 1526.doc version 1.1 22.05.2013 vectron international filter specification tfs 1526 3/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. stability characteristics, reliability after the following tests the filter shall meet the whole specification: 1. shock: 500g, 1 ms, half sine wave, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0,35 mm or 5 g respe ctively, 1 octave per min, 10 cycles per plane, 3 p lanes; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 15 min. each / 1 00 cycles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " air reflow temperature conditions" on page 4; this filter is rohs compliant (2002/95/eg, 2005/618 /eg) packing tape & reel: iec 286 ? 3, with exception of value f or n and minimum bending radius; tape type ii, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm g do w ct f e g d1 p2 p1 po bo ao pull off direction pin marker typ date code ko t a c n w 1 w 2 the minimum bending radius is 45 mm. tape (all dimensions in mm) w : 8,00 0,3 po : 4,00 0,1 do : 1,50 +0,1/-0 e : 1,75 0,1 f : 3,50 0,05 g(min) : 0,75 p2 : 2,00 0,05 p1 : 4,00 0,1 d1(min) : 1,50 ao : 3,25 0,1 bo : 3,25 0,1 ct : 5,3 0,1 reel (all dimensions in mm) a : 180 w1 : 8,4 +1,5/-0 w2(max) : 14,4 n(min) : 60 c : 13,0 0,2
filename: tfs 1526.doc version 1.1 22.05.2013 vectron international filter specification tfs 1526 4/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. air reflow temperature conditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/ second > 100c between 300 and 600 seconds > 150c between 240 and 500 seconds > 217c between 30 and 150 seconds peak temperature max. 260c time within 5c of actual peak temperature between 10 and 30 seconds cool-down rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds temperature / c time / s max. 260c 217c 10 ... 30 s 30 ... 150 s max. 300 s chip-mount air reflow profile
filename: tfs 1526.doc version 1.1 22.05.2013 vectron international filter specification tfs 1526 5/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. history version reason of changes name date 1.0 generation of development specification s.springfeldt 08.06.2011 1.1 generation of filter specification adding typical values adding typical performance s.springfeldt 22.05.2013
|
